Gas-dynamic analysis of the bandage seal of an LPI impeller manufactured by SLS printing

The development of additive technologies and polymer materials opens up new applications in mechanical engineering, particularly in turbine engineering. For instance, studies have already demonstrated the potential of using polyamide parts manufactured by SLS printing for low-flow turbine stages, with experimental investigations confirming their effectiveness. This manufacturing method allows the consideration of new shapes for elements of the flow part of gas turbines that cannot be produced by mechanical machining of workpieces. This article discusses a radial centripetal impeller of Leningrad Polytechnic University design, intended for use in an autonomous turbogenerator in a gas distribution line. This impeller features an adapted bandage seal designed to accommodate the specific requirements of SLS printing manufacture. The aim of this work is to demonstrate the effectiveness of the proposed seal design through a gas dynamic analysis of three stage variants: without a seal, with a bandage seal, and with a counter labyrinth on the stator. The calculation was performed at the design parameters, accounting for the circumferential periodicity of the stage in the Ansys CFX software package during the combined operation of the nozzle assembly and the impeller. The final comparison is made by calculating the adiabatic efficiency, determined from the power generated on the impeller (via torque) and the available power. Analysis of the results showed the positive effect of using this seal, especially for the variant with reciprocal labyrinth channels, indicating the feasibility of introducing this design into such machines and the need for further work to optimize the seal in terms of both gas-dynamic and strength properties.

1. Averyanov V. K., Davydov O. A., Kiryukhin S. N. Autonomous power supply of a gas distribution station using alternative energy sources // Plumbing, Heating, Air Conditioning 2020; (11): 64 – 69.

2. Finogeev D. Yu., Reshetnikova O. P. Additive technologies in modern production of precision engineering parts. Bulletin of the Saratov State Technical University 2020; (3): 86.

3. Strukov S. Yu., Golev I. M., Akberova E. M. Features of the application of additive technologies in military repair of aircraft equipment // Aerospace Forces. Theory and Practice 2025; (36): 138 – 147.

4. Adaptation of the design of a gas turbine unit fuel injector for the possibility of its production using SLM printing. M. A. Golubtsov, V. V. Barskov, A. M. Balakin, I. R. Nurkov, M. Basati Panakh, M. A. Laptev, K. A. Alisov. Gas Industry 2025; (4): 84 – 90.

5. Mechanistic models for additive manufacturing of metallic components. Wei H. L. et al. // Progress in Materials Science 2021; 100703.

6. Isakova T. A., Petrova P. N., Markova M. A. Study of polymer composite materials based on mechanically activated polytetrafluoroethylene. Journal of the Siberian Federal University. Engineering and Technology 2023; (8): 967 – 976.

7. Pobelyansky A. V., Levikhin A. A. Study of the capabilities of additive technologies in the creation of propulsion system elements. Additive technologies: present and future 2020; 19 – 36.

8. Markov A. D. Advanced Materials for SLS Printing. International Journal of Humanities and Natural Sciences 2022; (12 – 2): 150 – 155.

9. Tabatabaei B., Huang R., Choi J. W. Hoboken, NJ 3D Printing and Additive Manufacturing.: Wiley 2022: 267 – 309.

10. Experimental Development of Additively Manufactured Turboexpanders towards an Application in the ORC. Špale J. et al. Proceedings of the Heat Powered Cycles Conference, Bilbao, Spain 2022: 10 – 13.

11. Gai Z., Zhu P., Hu J. Effects of Sealing Flow Supply Configuration with Holes on Sealing Effectiveness of Turbine Rim Seal. Journal of Thermal Science 2023; (1): 366 – 386.

12. Afanasyev I. V., Granovsky A. V., Manaev I. A. Study of the influence of the casing design on losses in shroudless turbine blades. Thermal Power Engineering 2022; (8): 21 – 30.

13. Kryukov A. A., Chekhranov S. V. Three-dimensional numerical modeling of a low-flow centripetal turbine with partial blading of the runner. Bulletin of Astrakhan State Technical University. Series: Marine Engineering and Technology 2021; (1): 74 – 80.

14. Kachurin A. V., Ilyichev V. Yu. Development and testing of a methodology for numerical modeling of air flow in labyrinth seals of gas turbines. High-tech in instrument and mechanical engineering and the development of innovative activities at the university 2022: 176 – 181.

15. Zhao Yizhen, Wang Chunhua. Shape Optimization of Labyrinth Seals to Improve Sealing Performance. Aerospace 2021; 8(4): 92.